Installation

For the best results, be sure to complete the recommended preparation steps before installing your screen protector. Once finished, continue with the installation process specific to the type of protection you purchased.

Initial Steps

  • Wash and Dry Your Hands - Start by washing your hands thoroughly to remove oils or dirt that could transfer to the screen.
  • Clean the Phone Screen - Use the included wet wipe to clean the screen, removing fingerprints, dust, and oil. Follow with the dry wipe to dry the surface and remove streaks.
  • Remove Any Remaining Dust - Use the dust removal sticker to dab the screen. gently and lift any remaining dust particles. Even one speck of dust can cause bubbles, so be thorough.

Tempered Glass (no install tool)

  • Complete the initial above steps.
  • Remove the protective adhesive backing.
  • Visually align the protector with the edge of the device screen. (Pressing the power button to illuminate the device screen helps make the edge more clearly visible).
  • Lower the glass slowly onto the screen.
  • It should begin adhering on its own. Lightly press in the center and let the adhesive spread outwards.
  • Gently push out any remaining air bubbles by smoothing from the center toward the edges.
  • If included with purchase, make sure to register your FREE product guarantee within 30 days of purchase for up to $200 in coverage.

 

Tempered Glass (install tool included)

  • Complete the initial above steps.
  • Remove the protective backing, then position the Simple™ Easy Auto-Install Tool on your device, aligning the top of the tool with the top edge of your device.
  • Press down using moderate pressure inside the circle and the installation will begin.
  • Remove the tool, then gently push out any remaining air bubbles by smoothing from the center toward the edges.
  • If included with purchase, make sure to register your FREE product guarantee within 30 days of purchase for up to $200 in coverage.

 

Tempered Glass (dust free install tool)

  • Complete the initial above steps.
  • Align the top of the Simple™ Easy Auto-Install Tool with the top of your device, then place the tool onto the device.
  • Locate the #1 "PULL HERE" tab at the bottom of the install tool, and gently pull out the plastic sheet.
  • Find the #2 "START HERE" position, then press and slide your finger from left to right using consistent pressure.
  • Next, slide your finger upward through the open section of the install tool, applying steady, consistent pressure.
  • Lastly, wait 15 seconds, then remove the install tool along with the plastic cap sheet, gently pushing out any remaining air bubbles by smoothing from the center toward the edges.
  • If included with purchase, make sure to register your FREE product guarantee within 30 days of purchase for up to $200 in coverage.

Screen Protection Tips

  • Avoid touching the adhesive side of the protector.
  • If you trap a speck of dust under the glass, you may lift the edge with a fingernail or card and use the dust sticker to remove it.
  • Let it settle for a few minutes before using your device.

 

Liquid Glass


  • Complete the initial above steps.
  • Twist off the top of the Liquid Glass vial to open it completely.
  • Apply droplets evenly across the screen, using the entire contents of the vial. Immediately after, use the sponge to spread the liquid evenly over the entire screen surface.
  • Allow your device to dry for 5 minutes, then use the microfiber cloth to gently buff away any excess solution. The product will be fully cured after 24 hours.
  • Register your FREE product guarantee within 30 days of purchase for up to $200 in coverage.

 

Smart Watch Protection

Apple Watch Bumper

  • Clean your device thoroughly.
  • Remove the protective film from the product.
  • Align it with the Digital Crown® on your device.
  • Press and click it firmly into place to secure the fit.

 

 

Samsung Smart Watch Protection

  • Clean your device thoroughly.
  • Remove the protective backing from the product.
  • Align the product carefully with the edges of your watch.
  • Press down gently along the edges using your finger to eliminate any air bubbles.

 

Camera Lens Protector

  • Clean your camera lens thoroughly.
  • Remove the protective film from the product.
  • Align it with the camera lens on your device.
  • Press and click it firmly into place to secure the fit.